Shopping Cart Checkout Shipping Cost Download Website

Home

MP3 Player

8051 Tools

All Projects

PJRC Store

Site Map

You are here: MP3 Player Technical Docs Kit Assembly, Rev A Errata

Search PJRC

PJRC Store Main Board, $150 LCD & Pushbuttons, $42 LCD/Backlight/PB, $77 IDE Cable, $9 Complete Parts List MP3 Player Main Page Detailed Info User Photo Gallery Connecting The Board Firmware Download Side Projects Technical Docs Document Index Kit Assembly, Rev C Kit Assembly, Rev A Errata Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Win32 Compiler Firmware Library Calls Memory Map Data Sheets IR Remote Control Schematic, Rev C Schematic, Rev A Schematic, FPGA PCB Layout, Rev C PCB Layout, Rev A LCD Fonts LCD Protocol LCD Pushbuttons Using The STA013 72 Pin SIMM Old MP3 Player Design Freq. Asked Questions FAQ #2 News And Updates

Errata for MP3 Player Board Rev A

Because the board is packed so tightly (to allow it to fit into the 5.75 by 4 inch size), there are a number of components that are not properly marked. These are listed here. Please be careful when assembling the board, as there are several parts that look similar, but are in fact quite different. We have attempted to arrange the assembly steps and our packaging avoid similar appearance parts within each assembly step.

This errata list applies to MP3 player board, marked REV A, near the top edge of the 84 pin PLCC socket.

Corrections, Required To Make The Board Work

• Trace Cut, Pin 7 of 74HC165
  The trace between the 22k resistor network and pin 7 of the 74HC165 chip must be cut, to allow the CPU to access the flash rom chip.
• Trace Cut, Pin 15 of 74HC165, jumper to ground The trace between pins 15 and 16 of the 74HC165 must be cut. Pin 15 then must be connected to ground. We suggest soldering a short wire between pin 15 and the ground trace that runs under the chip on the solder side. This ground trace has a via near pin 3. This modification is required to allow the firmware to read the pushbuttons.

Figure 1: Trace Cut, Pin 7 of 74HC165

Figure 2: Trace Cut, Pin 15 of 74HC165, Jumper To Ground

Minor Issues

• IDE Interface Missing Pin 1 Marking Pin 1 of the IDE interface should be marked on the board. On both connectors, pin 1 is on the end facing the SIMM. Pin 1 is labeled on the assembly diagrams. Now would be a good time to mark pin #1 on your board with a permanent pen, to avoid connecting a drive's cable backwards.
• 44 Pin Header, Tight Fit
  The 44 pin header (Step 5) fits tightly. It can be tricky to insert this part, because the holes are so small. Do not apply excessive force, the part will press into the board without excessive force when it is aligned straight.
• 1N4737 Diode, Slight Bend Necessary To Fit SIMM Socket
  The 1N4737 diode (Step 10) may need to have its legs bend slightly to prevent it from obstructing the SIMM socket. We suggest that you try to fit the SIMM socket while this part is in the board but not yet soldered, to verify that this diode will not prevent you from correctly inserting the SIMM socket.

General Notes

• 33 pF Capacitors Not Marked
  The location of these parts is not marked on the board. Two of these capacitors are located by each crystal. These parts are included in Step 2.
• 0.1 µF Capacitors Not Marked
  This part is all over the board. The only indication of the location of the capacitors is an outline around each of the two holes for the part. There are 15 capacitors in the MP3 player (Step 4), and 9 in the power supply (Step 8). We suggest that you insert the 33 pF capacitors before these, because it's easy to place one of these where the 33 pF parts belong.
• 22k Resistor Network Not Marked
  The location of this part is not indicated on the board. Be very careful, not only is it directional, but it looks identical to the 4.7k resistor network. The 22k resistor network is located by the 6 push buttons. It is marked on the side with 8X-1-223. This side of the part needs to be facing the push buttons. This part is included in Step 2.
• 4.7k Resistor Network Not Marked
  Similar to the 22k resistor network, the location of this part is not indicated on the board. It is located by the 40 and 44 pin connectors. Be careful, it looks identical to the 22k resistor network. On the side of this part is the marking 8X-2-472. This part is included in Step 3.
• 100 µF Capacitors Not Marked
  The location of this part is not indicated on the board. Be very careful, this part looks almost identical to the 10 µF capacitor. There are circles on the board indicating that one of the two capacitors should be inserted. The positive wire is marked for the capacitor. This part is included in Step 4 and Step 10.
• 10 µF Capacitors Not Marked
  The location of this part is not indicated on the board. Be very careful, this part looks almost identical to the 100 µF capacitor. There are circles on the board indicating that one of the two capacitors should be inserted. The positive wire is marked for the capacitor. This part is included in Step 5 and Step 9.
• Parts Marked On The Board, But Not Used
  There are two parts that are marked on the board, but were subsequently removed from the design. Be sure NOT to insert any parts into the following locations:
  • A capacitor located between the 44 pin PLCC socket and the SIMM socket
  • A 69.8 k resistor located between the 34 pin connector and the SIMM socket
  These two parts form a RC reset circuit for the 87C52 CPU, which was replaced with a MAX810 surface mount IC (Step 1) on the solder side under the CPU. The MAX810 offers better performance. The capacitor can physically obstruct inserting some SIMMs.